Bay Windows Add Character And Area To A Home
It was the best spot. Our California cattle ranch design house had a big photo window in the front room. The window extended from a few inches above the flooring to just a couple of inches listed below the cathedral ceiling. The walls and ceiling were redwood stained knotty pine and the floor was a matching wood. The window kept an eye out over a flower bed, shrubs and the expanse of front yard. It was the ideal window to be replaced with a bay window.
The window was nearly square. It was 72 X 72 inches. We considered a bow window, however chosen to set up a bay window rather. We just felt that our specific house looked much better with three panel bay window rather than the numerous panel bow windows. Our intent was to fill the seat board of the bay with potted plants we had sitting in front of the existing photo window. The new plan would provide us a little more area in the room and improve the overall appearance of your home. It was time to go shopping.
Scratch vs. Pre-built
When we first understood of setting up the brand-new window, I began collecting prepare for building a bay window. Thumbing through books and publications, and the Web online search engine, I discovered a number of prepare for building a bay window from scratch. I also discovered that undertaking such a task was going to be unneeded. Most of the significant window makers, such as Pella, Milgard and Anderson make both completely pre-assembled bay windows in addition to pre-built elements for bay windows.
Installing a bay window can easily be a do-it-yourselfer job. Before you go the diy route, nevertheless, you may want to line up a professional to help out if needed. This is not going to be a job that you can complete during a Saturday afternoon. Possibilities are you are not going to finish it in a weekend, for that matter.
You Fix-It Right Plumbing are likewise going to wish to line up some help. Bay windows and window parts are heavy. At least they are too heavy for a single person to handle.
Be sure and take a look at the weather report, including the long range projection. Setting up the window means opening a hole into your home. It can take a number of days to get the new window in location and sealed. The last thing you desire is for rain to come gathering on your floor, walls or furnishings.
Be sure and inspect your city or neighborhood construction codes. There may be unique regional requirements, such as having shatterproof glass in low profile windows. You are probably going to require a structure license anyhow, so that is likewise a great time to inspect the codes.
Tools and Products Needed
The tools you will require for this task consist of a tape measure, a framing square that you can likewise utilize as a straight edge, a circular saw or miter saw, crow bars, drill and bits, level, stapler, utility knife, tin snips and a caulking gun.
The materials you will require consist of the bay window unit, the assistance brackets, nails, roofing paper, shingles, roofing nails, exterior grade silicone caulking and fiberglass insulation. You will likewise require 1X6 inch boards for the window https://www.fixitrightplumbing.com.au/plumber-yarraville/ skirting. If you are expanding an existing window, or if you are installing the window in a space that was formerly the wall, you will likewise need 2X4s for cripple studs and extra framing.
Basic Setup Steps
1. Develop window position in the wall. Remove the existing window. Determining the bay window, mark on the outside of your home the opening needed for the new window. Using your circular saw, cut the required opening.
2. Framing. Construct the framing for the brand-new window. This will likely consist of cutting through existing studs and putting in a brand-new header, rough sill, jack studs and cripple studs.
3. Set up the support braces. A window as much as 5 feet broad will take a minimum of two support braces. A broader window will need three.
4. Set the window in location. Raise the bay window on the support braces and slide it into the rough opening. Shim as essential to level the window. Anchor in place.
5. Construct the window roofing. Set the roof frame on top of the bay window system and nail in place. Fill the space between the roofing system and the top of the bay window with insulation. Fasten the roof sheeting to the frame and cover with roof paper. Set up the drip edges and the flashing and then shingle.
6. Set up the window skirting around the bottom of the window. Fill will insulation and then connect the skirt bottom to seal the underneath side of the window.
7. Seal the edges with silicone caulking.
This is a list of the fundamental installation steps and they have actually been abbreviated in the interests of simpleness and space. The window system you purchase will have complete setup steps. Take it from the voice of experience; it really makes the project go far more smoothly and it will be finished in much less time when you read and follow them.
In our case, I had 2 good friends helping with the task. We have actually interacted on other projects and work together well. We had the old window out and the rough framing finished on Saturday afternoon. We buttoned up the hole with plywood over night and went back to work the next day. By Sunday night we had the new window set up and the roof and skirting completed. On Monday afternoon I finished sealing up the outside and completed the trim work for the inside.
And, we were right. It was the ideal area for a bay window. It looked fantastic from the outside. Inside, it became the centerpiece of the room and included an unique charm to the house. The window offered your home added character and value.
When it came time to sell your home, it was one of the functions that were especially attractive to the purchasers.